By James Rodriguez, Central Chimney Service.
A wood-burning insert should be connected to a full stainless steel liner that runs from the insert outlet to the top of the chimney. Any other arrangement, including the old “slammer” install where the insert is simply pushed into the firebox with no connector at all, lets smoke and creosote collect in the smoke chamber and makes the insert nearly impossible to sweep properly. If you own an insert in Crest Hill and nobody has ever shown you a liner, this post explains what to look for and why it matters before the heavy burning season starts.
What a slammer install actually is
A slammer is an insert set into an existing masonry fireplace with nothing linking its flue collar to the chimney. The exhaust just dumps into the open firebox and finds its own way up. Installers used this shortcut for decades because it was fast and cheap, and we still find it in a surprising share of homes built in the 1970s and 1980s around Crest Hill and the older parts of Lockport Township.
The problem is physics. The insert outlet is usually 6 inches across. The masonry flue above it may be 12 by 12 inches or larger. Hot exhaust leaving a small opening into a much bigger, colder space slows down, cools, and drops its unburned vapor as creosote on the smoke shelf and lower flue tiles. The draft weakens, the fire smolders, and the cycle feeds itself. Over 29 years of sweeping I have pulled buckets of flaky third-stage creosote out of smoke chambers behind slammer inserts that the homeowner thought were fine.
Direct connect vs. full reline
There are two upgrade paths, and only one of them is a real fix. A “direct connect” uses a short section of stainless pipe from the insert collar up past the damper frame, then stops. It is better than nothing because it moves the exhaust above the smoke shelf, but the gas still expands into the oversized tile flue. A full reline runs a continuous flexible or rigid stainless liner from the insert to a new cap and plate at the chimney top. The liner is sized to the appliance, so the exhaust stays hot and moving all the way out.
Manufacturer instructions for modern EPA-rated inserts almost always call for the full liner, and NFPA 211, the standard we work to, treats a change of appliance as a trigger for a Level 2 inspection with a camera scan of the flue interior. That scan is what tells us whether the existing tiles are sound enough to hold a liner or need to be addressed first. Details on both paths are on our chimney relining service page.
How to tell what you have
You can check a few things yourself in ten minutes with a flashlight. Look behind or above the insert surround for the flue collar. If you see a stainless pipe disappearing upward, you have at least a direct connect. If you see open firebox brick and the old damper, you have a slammer. From outside, a full reline usually shows a stainless top plate and cap rather than the original clay tile poking out of the crown.
- Insert pulls hard to light and smokes back at the door: the exhaust is losing heat in the oversized flue.
- Glass blackens within one or two fires: the fire is not getting enough draft to burn clean.
- A sweet, tarry smell in the room on humid days: creosote sitting on the smoke shelf.
- Sweeps in the past said they “could not get behind the insert”: a classic sign nobody has ever cleaned the smoke chamber.
If two or more of those sound familiar, book a Level 2 inspection before you burn this season. We put a camera up the flue, pull the insert forward if needed, and show you exactly what is behind it.
Why this matters more in November
Inserts in our area run hard from now through March, and a slammer with a creosote-loaded smoke chamber is one hot fire away from a chimney fire you may never notice until the tiles crack. Insulated liners also keep the flue warm in sub-freezing weather, which reduces creosote and makes the insert easier to start on a cold morning. A liner job is far easier to schedule in November than in January when the flue is coated in ice.
We are insured and bonded, we quote the price up front, and our relining and inspection rates are listed openly on our pricing page. Call (815) 305-5510, 7 days a week, 7 AM to 7 PM, and tell us what brand of insert you have. We cover Crest Hill and the surrounding towns, and you can see the full list on our services hub.
Frequently asked questions
What is a slammer insert install?
A slammer is a wood insert pushed into a masonry fireplace with no pipe connecting its outlet to the chimney. Exhaust dumps into the firebox and rises through the oversized flue, which cools it and causes heavy creosote buildup.
Is a direct connect good enough for a wood insert?
A direct connect is an improvement over nothing, but it still leaves the exhaust expanding into a flue that is far too large. Most insert manufacturers and NFPA 211 practice point to a full stainless liner from insert to cap.
Why does an oversized flue cause creosote?
Exhaust leaving a 6-inch collar into a flue several times larger slows down and cools quickly. Cooler smoke condenses its vapor as creosote on the tiles and smoke shelf instead of carrying it outside.
Can you sweep an insert that has no liner?
Not thoroughly. The insert has to be pulled out to reach the smoke chamber, and the creosote behind it is often glazed. Many past sweeps simply brushed the flue from the top and never cleaned the chamber at all.
Does a wood insert need an insulated liner?
In the Crest Hill climate an insulated liner is the better choice. It keeps flue gases warm through winter, improves draft on cold starts, and reduces creosote. It also provides a thermal buffer if the old clay tiles are cracked.
Do I need an inspection before relining?
Yes. NFPA 211 calls for a Level 2 inspection with a camera scan whenever the appliance changes. The scan shows whether the existing flue can accept a liner or needs repair first.
How long does a full reline for an insert take?
Most insert reline jobs are finished in a single day. The insert is pulled, the liner is run from the top, connected at the collar, and finished with a new top plate and cap.
How much does relining for a wood insert cost?
Our relining and inspection rates are posted on our pricing page and quoted up front before any work starts. The final figure depends on chimney height and whether the liner is insulated.
Published November 8, 2026
