By James Rodriguez, Central Chimney Service.
Carbon monoxide alarms are the cheapest safety equipment in the house and the most commonly installed wrong. Every fall we walk into homes across Crest Hill and the surrounding towns we serve and find alarms sitting in a drawer, expired by four years, or plugged in on the opposite side of the basement from the appliances they are supposed to watch. Before the first cold night, this is a ten-minute job worth doing properly.
Where CO actually comes from in a house
Carbon monoxide is a byproduct of anything burning fuel: the furnace, the water heater, a gas fireplace, a gas range, a wood stove, an attached-garage vehicle. In a healthy system, that exhaust leaves through a flue or vent. CO becomes a problem when the exhaust path is blocked, disconnected, corroded, or drafting backward — which is why chimneys and CO alarms are part of the same conversation.
The chimney-side causes we find most often are a bird or squirrel nest packed into a flue, a collapsed clay tile, a disconnected vent connector at the water heater, a chimney cap crushed flat, or a flue that is far too large for the single appliance still using it. None of those announce themselves. The alarm is the backstop.
Placement: what the manufacturers say
Read the instructions that came with your specific alarm, because models differ. The consistent guidance across manufacturers and the current model codes is one alarm on every level of the home, including the basement, and one outside each separate sleeping area. If a bedroom contains a fuel-burning appliance, put one in that room too.
Keep them away from these spots
Do not mount an alarm directly above or beside a fuel-burning appliance, where normal startup puffs will nuisance-trip it. Avoid within about 15 feet of cooking appliances, humid bathrooms, ceiling fans, supply registers, and drafty windows. CO mixes with air rather than settling, so height matters less than people assume — a wall outlet at knee height and a ceiling mount both work.
The part almost everyone forgets: they expire
CO sensors wear out. Most units carry a service life of seven to ten years from the date of manufacture, printed on the back of the housing, not from the date you bought it. When it expires the unit chirps a fault pattern that people frequently mistake for a low battery, replace the battery, and move on. Check the manufacture date on every alarm in the house this month. If it is out of range, replace the unit — there is no way to refresh the sensor.
Test with the test button monthly. That button verifies the horn and circuitry, not the sensor’s sensitivity to gas, which is the reason the expiration date still governs.
If an alarm sounds
Get everyone outside into fresh air first, then call 911 or the gas utility from outside. Do not spend time hunting for the source, and do not silence the alarm and go back to bed. Once responders have cleared the house, the follow-up question is why it happened, and that is where an inspection of the venting comes in.
Pair the alarms with a look up the flue
Alarms tell you something already went wrong. An inspection keeps it from going wrong. A camera chimney inspection before heating season shows blockages, liner cracks, and disconnected connectors while they are still cheap to fix, and a chimney sweep clears the nests and buildup that cause backdrafting in the first place. Both are quoted from published prices on our pricing page.
We have been doing this work for 29 years, insured and bonded, with the price given before the job starts. Call (815) 305-5510 — seven days a week, 7 AM to 7 PM.
Frequently asked questions
How many carbon monoxide alarms does a house need?
The consistent guidance is one on every level including the basement, plus one outside each separate sleeping area. Add one inside any bedroom that contains a fuel-burning appliance.
High on the wall or low? Does CO sink?
Carbon monoxide mixes with room air rather than sinking or rising, so mounting height is far less important than location. Follow the height your specific model’s instructions specify and focus on keeping it away from vents, fans, and cooking areas.
How long does a CO alarm last?
Most units have a sensor life of roughly seven to ten years from the manufacture date printed on the back of the housing, not from the day it was purchased. After that the sensor cannot be refreshed and the unit is replaced.
My alarm keeps chirping but the battery is new. Why?
A repeating fault chirp after a fresh battery is very often an end-of-life signal. Check the manufacture date on the back before assuming it is a battery issue.
Does a chimney problem really trip a CO alarm?
It can. A blocked flue, a collapsed liner, a crushed cap, or a disconnected vent connector all interfere with exhaust leaving the house, and that exhaust carries carbon monoxide.
Do I need a CO alarm if I only have a wood-burning fireplace?
Yes. Wood combustion produces carbon monoxide as well, and a poorly drafting fireplace can push it into the room. Most homes also have a gas furnace or water heater regardless.
What should I do the moment an alarm sounds?
Move everyone outdoors into fresh air, then call 911 or the gas utility from outside. Do not search for the source and do not silence the alarm and go back inside.
Should the venting be checked after a CO event?
Yes. Once responders clear the house, the cause still needs to be found. A camera inspection of the flue and vent connectors shows whether the exhaust path is the reason.
Published September 21, 2026 · Last updated September 8, 2026
